Cara Menelepon 

Router>enable
Router#configure terminal
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#ip dhcp pool VOICE
Router(dhcp-config)#network 192.168.10.0 255.255.255.0
Router(dhcp-config)#default-router 192.168.10.1
Router(dhcp-config)#option 150 ip 192.168.10.1
Router(dhcp-config)#exit

Router(config)#ip dhcp excluded-address 192.168.10.1
Router(config)#telephony-service 
Router(config-telephony)#max-dn 5
Router(config-telephony)#max-ephones 5
Router(config-telephony)#ip source-address 192.168.10.1 port 2000
Router(config-telephony)#auto assign 4 to 6
Router(config-telephony)#auto assign 1 to 5
Router(config-telephony)#exit

[PINDAH SWITCH]

Switch>enable
Switch#configure terminal
Switch(config)#interface range fastEthernet0/1-5
Switch(config-if-range)#switchport mode access 
Switch(config-if-range)#switchport voice vlan 1


[PINDAH ROUTER]

Router(config)#ephone-dn 1
(Enter)
Router(config-ephone-dn)#number 54001
Router(config-ephone-dn)#exit

Router(config)#ephone-dn 2
(Enter)
Router(config-ephone-dn)#number 54002
Router(config-ephone-dn)#exit

Komentar

Posting Komentar

Postingan populer dari blog ini

Arduino Kran Otomatis

#include <LiquidCrystal_I2C.h> LiquidCrystal_I2C lcd(0x3F , 16, 2); const int pinTrig = 8; const int pinEcho = 9; const int kran = 13; int jarak; void setup() {  lcd.begin();  Serial.begin(9600);  pinMode(pinTrig, OUTPUT);  pinMode(pinEcho, INPUT);  pinMode(kran,OUTPUT);  digitalWrite(kran,LOW);   lcd.setCursor(00,00);   lcd.print(" BELAJAR LISTRIK ");   lcd.setCursor(00,01);   lcd.print ("dan ELEKTRONIK");   delay (1500);    lcd.clear(); } void loop() {   digitalWrite(pinTrig, HIGH); delayMicroseconds(10); digitalWrite(pinTrig, LOW); float durasi = pulseIn(pinEcho, HIGH); jarak =(durasi *0.034)/2; Serial.println (jarak ); if (jarak < 40) {   digitalWrite(kran,HIGH);   lcd.setCursor(00,00);   lcd.print("  TERUS   JAGA    ");   lcd.setCursor(00,01);   lcd.print ("   KEBERSIHAN    " ); } else {   digitalWrite(kran,LOW);   lcd.setCur...
Baca selengkapnya

Konfigurasi Arduino Tempat Sampah

#include <Wire.h>    #include <Servo.h> Servo myservo;  #define trigPin 8 #define echoPin 9  long duration;  int distance = 0;  int pos = 0;    void setup() {     myservo.attach(10); pinMode(trigPin, OUTPUT); // setting triggerpin sebagai output pinMode(echoPin, INPUT); // setting echopin sebagai Input Serial.begin(9600); // setting kecepatan pengiriman serial monitor } void loop() { digitalWrite(trigPin, HIGH);// aktifkan sensor ultrasonic delayMicroseconds(10); // selama 10 microseconds digitalWrite(trigPin, LOW); // matikan sensor ultrasonic duration = pulseIn(echoPin, HIGH); // baca rentan waktu dari trigPin High sampai echoPin high distance= duration*0.034/2; //konversi selang waktu ke CM if (distance < 30) // Hanya menampilkan jarak jika jaraknya kurang dari 300 cm / 3 meter { Serial.println(distance); // kirim data jarak ke PC    myservo.write(130);    delay(3000);   } else {   ...
Baca selengkapnya